What are the characteristics of the client VTP mode? (Choose two)
What is the final determining method of breaking a tie during the STP operation?
When configuring an EtherChannel bundle, which mode enables LACP only if a LACP device is detected?
What is the election of a designated port for a segment based on?
VLAN0001 has a Bridge ID priority of 32769. What makes up this value?
How is Telnet used to verify connectivity? (Choose two)
Which option should be used with the "switchport trunk allowed vlan" command to include specified VLANs in the existing list of allowed VLANs on a trunk link?
Which spanning-tree standard improves convergence over 1998 STP by adding roles to ports and enhancing BPDU exchanges?
Which issues can be caused by a redundant switch topology? (Choose three)
When electing a root port for a nonroot switch, which values are used to break ties if required? (Choose two)
VLAN 10 has a priority of 4096 and VLAN 20 has a priority of 16384. VLAN 20 has a lower MAC address than VLAN 10. What would be the likely result of running the "spanning-tree vlan 20 root primary" command for VLAN 20?
What guidelines must be followed to successfully form an EtherChannel bundle? (Choose two)
You are configuring HSRP for VLAN 10. You want its primary default gateway to be R1 and secondary default gateway be R2. What should you consider when configuring HSRP for R1? (Choose two)
While configuring a switch, you noticed a configuration issue with an EtherChannel bundle. You thought you corrected the issue, but the change didn't take effect on the EtherChannel bundle. What is the mostly likely cause of this problem?
What are the considerations when using First Hop Redundancy Protocols? (Choose two)
What are the possible consequences of an STP failure? (Choose two)
What options should be checked when troubleshooting end-to-end connectivity? (Choose three)
What command is used to verify MAC address table entries?
Which VTP mode forwards advertisements but does not synchronize VLAN configuration?
What steps are required to configure the IP SLA ICMP Echo test? (Choose three)
What are the valid encapsulation methods when forcing a device to become a trunk port? (Choose three)
All of the switches in your VTP domain are operating as servers. Which command changes the operation mode of DSW2 to client?
How can you solve congestion issues from multiple links aggregating on a switch without scaling issues?
You have configured your PC with multiple default gateways. R1 is the primary default gateway. R2 is the secondary default gateway. What is the best action to ensure redundancy of the default gateway if R1 goes down?
What are the considerations when using Cisco PVST+? (Choose two)
You have verified the interface status with the "show interface" command. What other steps should you consider when troubleshooting the physical connectivity between devices? (Choose three)
What can VLANs be used for? (Choose two)
You have changed the domain name for one server in a VTP domain to Sales. What happens to other servers with a domain name of null in the same VTP domain area?
What is the default mode of STP running on a Cisco Catalyst switch?
Which STP standards cannot be used when you have a mixed topology with Cisco and non-Cisco devices? (Choose three)
What information is returned from the "show spanning-tree vlan vlan_id" command? (Choose three)
What are the considerations when using the "switchport trunk native vlan vlan_number" command? (Choose three)
Which state of the default STP configuration allows ports to listen for BPDUs but not send any?
If both the cost and upstream BID are tied, which BPDU value is used to break this tie?
Why doesn't increasing the number of uplinks solve congestion issues from multiple links aggregating on a switch?
You want to disable the negotiation of trunking for all FastEthernet ports. Which commands are required to do this? (Choose two)
Which command would you use to specify a VLAN's ID on a switch?
When are VTP messages sent to clients for synchronization while using a VTP server? (Choose two)
You need to associate fastEthernet0/1 and fastEthernet0/2 with VLAN 10. Which commands would you use to do this? (Choose two)
You have determined that RSTP is creating problems on your network. You want to enable PortFast on your 24 port switch to rectify these problems. Which commands will do this on all 24 ports? (Choose two)
What command is used to verify ARP cache entries?
What protocols exist to negotiate EtherChannel creation and maintenance? (Choose two)
When using the "show etherchannel summary" command, what does the "u" flag signify?
What are the characteristics of a VLAN? (Choose two)
You have configured one side of your EtherChannel as passive. What mode should you use on the other side?
When operating in trunk mode, what command is used to shut off DTP?
Which priority value should you set for a switch to give it the best chance of remaining as a root bridge in the long term?
What is the best method of ensuring that your preferred switch is the root bridge?
What are the considerations when operating in the VTP transparent mode? (Choose two)
What are the common functions for IP SLA measurements when troubleshooting? (Choose three)
Which ports go into a blocking state in the final step of the spanning-tree algorithm?
When creating a trunk port, which "switchport mode" option sets the trunking mode to access unconditionally?
You have HRSP configured on your network with R1 as the active default gateway and R2 as the standby default gateway. What is the best way to configure PC1 to ensure that it is using a redundant default gateway?
You have a network that uses HRSP. What is the simple way to determine that HSRP is being used from the PC?
Output from the "show interface" command indicates that input queue drops are occurring. What does this signify?