CCNP Security Practice Test | Secure Mobility (SIMOS)

Exam: 300-209

Question 1 / 15

90:00

Which two protocols can be used for IPSec VTI encapsulation? (Choose two)

A. IKE

B. ISAKMP

C. AH

D. ESP

You are configuring DMVPN on a spoke router. The configurations in the output given below have been made on the router.
Which command or set of commands will complete the next step in the configuration on the spoke router?

You are configuring DMVPN on a spoke router. The configurations in the output given below have been made on the router.<br />Which command or set of commands will complete the next step in the configuration on the spoke router?

A. Router1(config-if)#tunnel protection ipsec profile MYIPSECPROFILE

B. Router1(config-if)#ip nhrp network-id 1
Router1(config-if)#ip nhrp authentication HdRtKqX5ZdYaZQjSYPqb
Router1(config-if)#ip nhrp nhs 10.1.1.1
Router1(config-if)#ip nhrp map multicast 172.17.0.1
Router1(config-if)#ip nhrp map

C. Router1(config)#interface Tunnel 0
Router1(config-if)#tunnel mode gre multipoint
Router1(config-if)#tunnel source GigabitEthernet0/0
Router1(config-if)#tunnel key 12345

D. Router1(config-if)#ip address 10.1.1.2 255.255.0.0
Router1(config-if)#ip mtu 1400

Which statement is true regarding a Cisco ASA security appliance and IPSec?

A. AH is not supported.

B. IKEv2 is supported but IKEv1 is not supported.

C. ISAKMP is supported but IKE is not supported.

D. ESP is not supported.

When configuring an IPSec profile to support IKEv2 and Cisco AnyConnect, what should you do immediately after enabling IKEv2 on the outside interface, choosing an interface certificate, and enabling Client Services?

A. Create an IKEv2 group

B. Connect and update the client profile

C. Create and edit a Cisco AnyConnect connection profile

D. Create and edit a client connection profile

Before deploying a basic site-to-site VPN, what information should you have? (Choose three)

A. ISAKMP policy

B. Transmission protection

C. Transform set

D. PSK

E. Basic peer authentication

What is the first required step in configuring a DMVPN spoke?

A. Configure an IPSec profile with an optional transform set

B. Create an mGRE tunnel interface

C. Generate or configure hub authentication credentials

D. Associate the IPSec profile with the mGRE interface

What improvements does IKEv2 provide to IKEv1? (Choose three)

A. Supports dynamically addressed peers with PKI-facilitated authentication

B. Built-in DPD

C. Supports PFS to ensure that a given IPSec SA key is not derived from another secret

D. Better rekeying and collision handling

E. Requires fewer round trips

What is the purpose of FlexVPN? (Choose two)

A. To provide encapsulation

B. To convert cleartext to ciphertext

C. To simplify deployment of VPNs

D. To address the complexity of multiple solutions

A user indicates that they are unable to access a file server share. You believe that you have misconfigured webtype ACLs.
What is the easiest method of verifying this?

A. View the Cisco ASA's logging output.

B. View predefined bookmarks.

C. View output from the traceroute command.

D. View DNS group configuration.

Refer to the output. Which statements regarding the output are true? (Choose two)

Refer to the output. Which statements regarding the output are true?

A. IKE Phase 2 was successful.

B. IPSec SAs were successfully completed.

C. IKE proposals are mismatched.

D. Conflicting group and IP addresses exist.

A connection is not forming between the spoke and the hub. Enter the command that you would use to verify SA states on hub and spoke. (Choose two)

A. show crypto session

B. show crypto session detail

Which two statements regarding the version of IKE used with FlexVPN are true? (Choose two)

A. It uses stateless cookies.

B. It can only be used with IPSec.

C. It operates over UDP port 4500.

D. It supports NAT traversal over UDP port 500.

E. Each peer maintains its own local policy.

When configuring HA headended designs, at least how many tunnels should be configured on each branch?

A. One

B. Three

C. Four

D. Two

What should you consider when configuring split tunneling in a Group Policy? (Choose two)

A. You can select the traffic that the clients will forward through the tunnel

B. By default, all traffic is forwarded through the tunnel using the exclude network list

C. It causes all the client traffic to go through the VPN tunnel

D. It permits the clients the direct access to external resources

Review the output. Which type of VPN technology has been configured?

A. FlexVPN

B. DMVPN

C. IPSec VPN

D. GETVPN

While calculating your results take a moment to complete our simple survey!
How likely is it that you would recommend LearnCisco.net to a friend or colleague?
0	1	2	3	4	5	6	7	8	9	10

Not at all likely								Extremely likely
Why?

While calculating your results take a moment to complete our simple survey!

How likely is it that you would recommend LearnCisco.net to a friend or colleague?

Why?

How likely is it that you would recommend LearnCisco.net
to a friend or colleague?